Home > Solutions > Industrial > RMS > Connectivity HW > RMS1500

RMS1500

The ideal Remoted Monitoring Solution for monitoring oil and gas production and transportation assets.

With its support for a wide range of wireless communications options and high I/O count, the RMS1500 delivers unparalleled value, performance, and reliability. The Iridium option, which uses a constellation of over 60 low earth orbit satellites, allows it to communicate in areas where cellular is not available and where the ground cover and terrain prove difficult for other satellite technologies. The base product provides 4 digital inputs, 1 digital output & 4 analog inputs, An optional I/O module is available with support for an additional 20 I/O points.

Features & Benefits

  • Class 1 Division 2, Groups A, B, C, D certified terminal meets industry standards for electronic equipment in Oil and Gas markets.
  • Modbus protocol interfaces directly with common SCADA devices such as RTU, PLC and flow meters to quickly and easily implement reporting and telemetry capabilities for remote equipment.
  • RS485 serial interface allows connection to SCADA devices over large distances to enable flexible deployment in a wide range of operating conditions.
  • Seamless global coverage based on the Iridium satellite constellation enables operational benefits in remote regions.
  • GSM and CDMA cellular modems also supported.
  • Expanded operating temperature range allows reliable deployment in some of the world’s most demanding environments.
  • Immediate reporting of digital status change (all data sent with report).
  • Over-the-air programming enables M2M to remotely reconfigure parameters such as threshold levels or report frequency.

Specifications

PHYSICAL
Size: 6.5” L x 3.5” W x 2.2” H (16.5 cm L x 8.9 cm W x 5.6 cm H)

ELECTRICAL
Solar charger Input: 14VDC to 30VDC
Battery Input: 10VDC to 16VDC
In circuit transient protection
Base power consumption (no modem) <100 mW @ 12VDC

COMMUNICATIONS
SATELLITE
  Iridium
  IsatDataPro 
CELLULAR
  CDMA
  GSM

CERTIFICATIONS / COMPLIANCE
Satellite: Iridium Network Approved
Class 1 Div 2 for use in hazardous locations (excl. additional I/O)

EXTERNAL INTERFACES
Serial:
  Qty (1) RS232 or RS485 (software selectable) communications port
  Supports optional I/O (RMS1501) & a wide variety of Modbus slave devices
  Qty (1) RS232 maintenance port

STANDARD I/O
Qty (4) digital inputs (contact closure or pulse accumulation)
Qty (1) digital open collector output, 15Vdc @ 100 mA max
Qty (4) analog input, 0-5V or 4-20 mA (with external 250 ohm resistors)

INTERNAL INPUTS
Battery voltage, charger voltage, ambient temperature

PROGRAMMING CAPABILITIES
Remotely programmable or via local utilities
Up to 10 multiple variable poll strings and 50 analog readings plus up to 64 digital status/alarms
High-high, high, low, and low-low alarm settings on each reading
Change of state alarms on digital inputs Multiple options on control output:
Active on alarm trigger, external sensor enable, timed pulse
Programmable poll type (10), size (1-50), protocol, and poll rate
Programmable record rate and post rate
Programmable data averaging on each reading (50)
Programmable analog data rolling average (50)
Slope and Offset Adjustments on all readings allows conversions of raw readings to engineering units

OPTIONS
Additional I/O module
Qty (24) digital inputs
Qty (8) digital outputs
Qty (4) analog input, 0-5V or 4-20 mA (with external 250 ohm resistors)
NEMA 4X polycarbonate enclosure

TYPICAL RMS1500 SYSTEM SCHEMATIC




© 2017 M2M Data Corporation. All Rights Reserved. Website by Trulium. >M2M Blog